Pages

Wednesday, May 15, 2013

Access Class Barring in LTE using System Information Block Type 2


As per 3GPP TS 22.011 (Service accessibility):

All UEs are members of one out of ten randomly allocated mobile populations, defined as Access Classes (AC) 0 to 9. The population number is stored in the SIM/USIM. In addition, UEs may be members of one or more out of 5 special categories (Access Classes 11 to 15), also held in the SIM/USIM. These are allocated to specific high priority users as follows. (The enumeration is not meant as a priority sequence):
Class 15 - PLMN Staff;
 -"-  14 - Emergency Services;
 -"-  13 - Public Utilities (e.g. water/gas suppliers);
 -"-  12 - Security Services;
 -"-  11 - For PLMN Use.

Now, in case of an overload situation like emergency or congestion, the network may want to reduce the access overload in the cell. To reduce the access from the UE, the network modifies the SIB2 (SystemInformationBlockType2) that contains access barring related parameters as shown below:




For regular users with AC 0 – 9, their access is controlled by ac-BarringFactor and ac-BarringTime. The UE generates a random number
– “Rand” generated by the UE has to pass the “persistent” test in order for the UE to access. By setting ac-BarringFactor to a lower value, the access from regular user is restricted (UE must generate a “rand” that is lower than the threshold in order to access) while priority users with AC 11 – 15 can access without any restriction

For users initiating emergency calls (AC 10) their access is controlled by ac-BarringForEmergency – boolean value: barring or not

For UEs with AC 11- 15, their access is controlled by ac-BarringForSpecialAC - boolean value: barring or not.


The network (E-UTRAN) shall be able to support access control based on the type of access attempt (i.e. mobile originating data or mobile originating signalling), in which indications to the UEs are broadcasted to guide the behaviour of UE. E-UTRAN shall be able to form combinations of access control based on the type of access attempt e.g. mobile originating and mobile terminating, mobile originating, or location registration.  The ‘mean duration of access control’ and the barring rate are broadcasted for each type of access attempt (i.e. mobile originating data or mobile originating signalling).

Another type of Access Control is the Service Specific Access Control (SSAC) that we have seen here before. SSAC is used to apply independent access control for telephony services (MMTEL) for mobile originating session requests from idle-mode.

Access control for CSFB provides a mechanism to prohibit UEs to access E-UTRAN to perform CSFB. It minimizes service availability degradation (i.e. radio resource shortage, congestion of fallback network) caused by mass simultaneous mobile originating requests for CSFB and increases the availability of the E-UTRAN resources for UEs accessing other services.  When an operator determines that it is appropriate to apply access control for CSFB, the network may broadcast necessary information to provide access control for CSFB for each class to UEs in a specific area. The network shall be able to separately apply access control for CSFB, SSAC and enhanced Access control on E-UTRAN.

Finally, we have the Extended Access Barring (EAB) that I have already described here before.

5 comments:

  1. Hi
    How eNB calculate ACB factor?
    which parameter are needed to calculate this factor?

    ReplyDelete
  2. Hello.
    ACB also have a time for backoff. How eNB calculate ACB factor and ACB time?

    ReplyDelete
  3. Hi, please advice if simcard with access class (11-15) will be able get service from barred cell?

    ReplyDelete
  4. >Hi, please advice if simcard with access class (11-15) will be able get service from barred cell?

    As the post says, "For UEs with AC 11- 15, their access is controlled by ac-BarringForSpecialAC - boolean value: barring or not."

    ac-BarringForSpecialAC represents Access Class for UEs. A = 11, B = 12, C = 13, D = 14, E = 15

    If ac-BarringForSpecialAC has the value 00010, it means that it is not barred for Access class 14 but barred for Access class 11, 12, 13 & 15

    ReplyDelete
  5. Hi, Please help me to understand how AC_BarringSkipForSMS-12 work.

    ReplyDelete