ITU has just agreed on key 5G performance requirements for IMT-2020. A new draft report ITU-R M.[IMT-2020.TECH PERF REQ] is expected to be finally approved by ITU-R Study Group 5 at its next meeting in November 2017. The press release says "5G mobile systems to provide lightning speed, ultra-reliable communications for broadband and IoT"
The following is from the ITU draft report:
The key minimum technical performance requirements defined in this document are for the purpose of consistent definition, specification, and evaluation of the candidate IMT-2020 radio interface technologies (RITs)/Set of radio interface technologies (SRIT) in conjunction with the development of ITU-R Recommendations and Reports, such as the detailed specifications of IMT-2020. The intent of these requirements is to ensure that IMT-2020 technologies are able to fulfil the objectives of IMT-2020 and to set a specific level of performance that each proposed RIT/SRIT needs to achieve in order to be considered by ITU-R for IMT-2020.
Peak data rate: Peak data rate is the maximum achievable data rate under ideal conditions (in bit/s), which is the received data bits assuming error-free conditions assignable to a single mobile station, when all assignable radio resources for the corresponding link direction are utilized (i.e., excluding radio resources that are used for physical layer synchronization, reference signals or pilots, guard bands and guard times).
This requirement is defined for the purpose of evaluation in the eMBB usage scenario.
The minimum requirements for peak data rate are as follows:
– Downlink peak data rate is 20 Gbit/s.
– Uplink peak data rate is 10 Gbit/s.
Peak spectral efficiency: Peak spectral efficiency is the maximum data rate under ideal conditions normalised by channel bandwidth (in bit/s/Hz), where the maximum data rate is the received data bits assuming error-free conditions assignable to a single mobile station, when all assignable radio resources for the corresponding link direction are utilized (i.e. excluding radio resources that are used for physical layer synchronization, reference signals or pilots, guard bands and guard times).
This requirement is defined for the purpose of evaluation in the eMBB usage scenario.
The minimum requirements for peak spectral efficiencies are as follows:
– Downlink peak spectral efficiency is 30 bit/s/Hz.
– Uplink peak spectral efficiency is 15 bit/s/Hz.
User experienced data rate: User experienced data rate is the 5% point of the cumulative distribution function (CDF) of the user throughput. User throughput (during active time) is defined as the number of correctly received bits, i.e. the number of bits contained in the service data units (SDUs) delivered to Layer 3, over a certain period of time.
This requirement is defined for the purpose of evaluation in the related eMBB test environment.
The target values for the user experienced data rate are as follows in the Dense Urban – eMBB test environment:
– Downlink user experienced data rate is 100 Mbit/s.
– Uplink user experienced data rate is 50 Mbit/s.
5th percentile user spectral efficiency: The 5th percentile user spectral efficiency is the 5% point of the CDF of the normalized user throughput. The normalized user throughput is defined as the number of correctly received bits, i.e., the number of bits contained in the SDUs delivered to Layer 3, over a certain period of time, divided by the channel bandwidth and is measured in bit/s/Hz.
This requirement is defined for the purpose of evaluation in the eMBB usage scenario.
– Indoor Hotspot – eMBB - Downlink: 0.3 bit/s/Hz Uplink: 0.21 bit/s/Hz
– Dense Urban – eMBB - Downlink: 0.225 bit/s/Hz Uplink: 0.15 bit/s/Hz
– Rural – eMBB - Downlink: 0.12 bit/s/Hz Uplink: 0.045 bit/s/Hz
Average spectral efficiency: Average spectral efficiency is the aggregate throughput of all users (the number of correctly received bits, i.e. the number of bits contained in the SDUs delivered to Layer 3, over a certain period of time) divided by the channel bandwidth of a specific band divided by the number of TRxPs and is measured in bit/s/Hz/TRxP.
This requirement is defined for the purpose of evaluation in the eMBB usage scenario.
– Indoor Hotspot – eMBB - Downlink: 9 bit/s/Hz/TRxP Uplink: 6.75 bit/s/Hz/TRxP
– Dense Urban – eMBB - Downlink: 7.8 bit/s/Hz/TRxP Uplink: 5.4 bit/s/Hz/TRxP
– Rural – eMBB - Downlink: 3.3 bit/s/Hz/TRxP Uplink: 1.6 bit/s/Hz/TRxP
Area traffic capacity: Area traffic capacity is the total traffic throughput served per geographic area (in Mbit/s/m2). The throughput is the number of correctly received bits, i.e. the number of bits contained in the SDUs delivered to Layer 3, over a certain period of time.
This requirement is defined for the purpose of evaluation in the related eMBB test environment.
The target value for Area traffic capacity in downlink is 10 Mbit/s/m2 in the Indoor Hotspot – eMBB test environment.
User plane latency: User plane latency is the contribution of the radio network to the time from when the source sends a packet to when the destination receives it (in ms). It is defined as the one-way time it takes to successfully deliver an application layer packet/message from the radio protocol layer 2/3 SDU ingress point to the radio protocol layer 2/3 SDU egress point of the radio interface in either uplink or downlink in the network for a given service in unloaded conditions, assuming the mobile station is in the active state.
This requirement is defined for the purpose of evaluation in the eMBB and URLLC usage scenarios.
The minimum requirements for user plane latency are
– 4 ms for eMBB
– 1 ms for URLLC
assuming unloaded conditions (i.e., a single user) for small IP packets (e.g., 0 byte payload + IP header), for both downlink and uplink.
Control plane latency: Control plane latency refers to the transition time from a most “battery efficient” state (e.g. Idle state) to the start of continuous data transfer (e.g. Active state).
This requirement is defined for the purpose of evaluation in the eMBB and URLLC usage scenarios.
The minimum requirement for control plane latency is 20 ms. Proponents are encouraged to consider lower control plane latency, e.g. 10 ms.
Connection density: Connection density is the total number of devices fulfilling a specific quality of service (QoS) per unit area (per km2).
This requirement is defined for the purpose of evaluation in the mMTC usage scenario.
The minimum requirement for connection density is 1 000 000 devices per km2.
Energy efficiency: Network energy efficiency is the capability of a RIT/SRIT to minimize the radio access network energy consumption in relation to the traffic capacity provided. Device energy efficiency is the capability of the RIT/SRIT to minimize the power consumed by the device modem in relation to the traffic characteristics.
Energy efficiency of the network and the device can relate to the support for the following two aspects:
a) Efficient data transmission in a loaded case;
b) Low energy consumption when there is no data.
Efficient data transmission in a loaded case is demonstrated by the average spectral efficiency
This requirement is defined for the purpose of evaluation in the eMBB usage scenario.
The RIT/SRIT shall have the capability to support a high sleep ratio and long sleep duration. Proponents are encouraged to describe other mechanisms of the RIT/SRIT that improve the support of energy efficient operation for both network and device.
Reliability: Reliability relates to the capability of transmitting a given amount of traffic within a predetermined time duration with high success probability
This requirement is defined for the purpose of evaluation in the URLLC usage scenario.
The minimum requirement for the reliability is 1-10-5 success probability of transmitting a layer 2 PDU (protocol data unit) of 32 bytes within 1 ms in channel quality of coverage edge for the Urban Macro-URLLC test environment, assuming small application data (e.g. 20 bytes application data + protocol overhead).
Proponents are encouraged to consider larger packet sizes, e.g. layer 2 PDU size of up to 100 bytes.
Mobility: Mobility is the maximum mobile station speed at which a defined QoS can be achieved (in km/h).
The following classes of mobility are defined:
– Stationary: 0 km/h
– Pedestrian: 0 km/h to 10 km/h
– Vehicular: 10 km/h to 120 km/h
– High speed vehicular: 120 km/h to 500 km/h
Mobility classes supported:
Indoor Hotspot – eMBB: Stationary, Pedestrian
Dense Urban – eMBB: Stationary, Pedestrian, Vehicular (up to 30 km/h)
Rural – eMBB: Pedestrian, Vehicular, High speed vehicular
Mobility interruption time: Mobility interruption time is the shortest time duration supported by the system during which a user terminal cannot exchange user plane packets with any base station during transitions.
This requirement is defined for the purpose of evaluation in the eMBB and URLLC usage scenarios.
The minimum requirement for mobility interruption time is 0 ms.
Bandwidth: Bandwidth is the maximum aggregated system bandwidth. The bandwidth may be supported by single or multiple radio frequency (RF) carriers. The bandwidth capability of the RIT/SRIT is defined for the purpose of IMT-2020 evaluation.
The requirement for bandwidth is at least 100 MHz.
The RIT/SRIT shall support bandwidths up to 1 GHz for operation in higher frequency bands (e.g. above 6 GHz).
Related posts:
- Some more thoughts on 5G
- 5G Network Architecture and Design Update - Jan 2017
- 5G New Radio (NR), Architecture options and migration from LTE
- LTE-Advanced Pro (a.k.a. 4.5G)
- Gigabit LTE?
- 4G / LTE by stealth
In other words, 5G will be all things to all people.
ReplyDeleteI wonder how this will turn out.
Thanks , good info !!
ReplyDelete