Showing posts with label inter-gNB-CU Handover. Show all posts
Showing posts with label inter-gNB-CU Handover. Show all posts

Thursday, December 17, 2020

Conditional Handover (Rel. 16) Explained

Although a couple of SON mobility robustness features have been introduced in LTE radio networks it is still a common problem in some network areas that a high number of handover failures leads to higher drop rates and large numbers of RRC Re-Establishments.

Often these problems occur due to quickly changing radio conditions in the handover preparation phase or after handover execution attempt. 

SON algorithms cannot cope with these dynamic changes of the environment, but improvement is possible if the UE itself is enabled to constantly monitor the radio quality during the handover procedure and finally select the best possible target cell from a list of candidate neighbors. This new feature defined in 3GPP Release 16 for both, NG RAN (5G SA NR) as well as E-UTRAN (LTE), is called "Conditional Handover". The figure below illustrates how it works.

(click on the picture to enlarge)

Step 1 is the RRC Measurement Report indicating that handover to a neighbor cell is required. However, this message contains a list of candidate neighbor cells.

In the figure it is assumed that each of these candidate cells is controlled by a different gNB. Hence, 3 XnAP Handover Preparation procedures are performed and each potential target gNB allocates radio resources for the UE and provides a handover command (NR RRC Reconfiguration message) that is sent back to the source gNB (step 2).

In step 3 the source gNB builds the conditional handover command, which is a NR RRC Reconfiguration message that contains a list of conditional reconfiguration options plus additional RRC measurement configurations that enable the UE to find out which of the possible target cells is the best fit. 

In step 4 the UE makes its handover decision and moves to the cell controlled by target gNB 1.

Here it sends in step 5 the NR RRC Reconfiguration Complete message. 

The target gNB 1 detects the handover completion based on the reception of the NR RRC Reconfiguration Complete message, performs NGAP Path Switch procedure (not shown in figure) and triggers the release of the UE context in source gNB on behalf of sending the XnAP UE Context Release message (step 6).

With this information the source gNB also detects the successful handover completion and orders in step 7 the release of the radio resources provided by target gNB 2 and 3 to which it sends the new XnAP Conditional Handover Cancel message.

As mentioned before the conditional handover is also possible for LTE radio connections. In this case X2AP is used instead of XnAP and LTE RRC instead of NR RRC.

The conditional handover can be performed for all kind of intra-eNB/gNB handover and X2/Xn handover. However, S1/N2 (NG-C) conditional handover is not allowed.


Tuesday, June 30, 2020

A Look into 5G Virtual/Open RAN - Part 6: Inter-gNB CU Handover involving Xn

In previous blog posts I have discussed intra-gNB-DU handover and inter-gNB-DU handover scenarios.Now it is time to look at inter-gNB-CU handover that uses the Xn interface.

At the RRC protocol layer there will be the measurement setups and measurement reports as in the intra-gNB handover cases. And F1AP UE Context Setup and Release Procedures are identical with the ones discussed for inter-gNB-DU handover. Only the cause values are expected to be different, e.g. "successful handover".

Thus, I do not want to  focus here on la adder diagram call flow (that is by the way very well described in 3GPP 38.401, chapter 8.9.4), but invite you to have a look at a "big picture" that you see below.

(click image to enlarge)

What characterizes the inter-gNB handover is the transfer of the UE RRC/NGAP context form the source gNB-CU to the target gNB-CU. When the Xn interface is available to connect two neighbor gNBs this context transfer is executed using the XnAP Handover Preparation procedure. The Initiating Message of this procedure transfers the UE context parameters to the target gNB-CU. Then embedded in the Successful Outcome message the handover command is sent in return to the source gNB-CU that forwards it to the UE. In addition a temporary user plane transport tunnel for the purpose of data forwarding is established and later on released on the Xn user plane interface.

Once the UE performed the handover on the radio interface all the transport tunnels for the payload transmission need to be switched from the old gNB to the new one. This includes the tunnel to the UPF that is managed by the NGAP. Thus, the target gNB-CU starts the NGAP Path Switch procedure. 

In the target gNB environment it is necessary to establish a new F1AP UE context, new E1AP Bearer Context and new F1-U payload transport tunnel. All this happens BEFORE the Handover Command is sent to the source gNB/UE. And once there is an indication that the handover is completed all the radio and transport resources controlled by the source gNB will be released.

So the figure above looks complicated, but actually the underlying logic of context/data forwarding, radio resource allocation and transport tunnel switching is quite simple.

Special note: In case there is no Xn interface available the UE context/handover information can be transmitted using NGAP Handover Preparation procedure on the source side of the connection and NGAP Handover Resource Allocation procedure on the target side of the connection.

Related Posts: