M2M, Cellular and Small Cells

I have written a post on this topic in the Cisco Service Provide Mobility blog here. The article is embedded as follows:

Feel free to add any comments you may have on the blog post here.

Mobile Relay Nodes (MRN) in Rel-12

Interesting article in IEEE Comms Magazine (embedded below) about the Moving Relay Node (MRN). 3GPP has done a study on a similar topic available in 3GPP TR 36.836. To make the case for the MRN they provide a reference scenario of high speed train

The TGV Eurostar in Europe is 393 m long, moves at speed reaching 300 km/h. The Shinkansen in Japan has similar characteristics, with 480 m long, 300 km/h of commercial speed. The high speed train in China is 432 m long moving at speed reaching 350 km/h.

Due to fast moving and well shield carriage, the network in high speed train scenario faces severe Doppler frequency shift and high penetration loss, reduced handover success rate and increased power consumption of UEs.

To improve the coverage of the train deployment, access devices can be mounted on the high speed train, providing a wireless backhaul connection via the eNBs along the railway by outer antenna e.g. installed on top of the train, and wireless connectivity to the UEs inside carriages by inner antenna installed inside.

MRN is a good solution but when it has to operate alongside with many other technologies can pose challenges. The IEEE article summarises it as follows:

Furthermore, new challenges regarding interference management arise due to the use of MRNs. As the distance between an MRN and the vehicular UE served by it is very short, the MRN and the vehicular UE can communicate with each other using very low power. In addition, the VPL can further help to dampen the signal of the MRN access link that propagates out from the vehicle. Thus, compared to direct transmission, the use of MRNs generates less interference from the access link, for both downlink and uplink, to UE outside the vehicles. This is appreciated in a densely deployed urban scenario where link availabilities are usually dependent on interference rather than coverage. For the backhaul link, however, the problem becomes complicated, as interference is expected both between different MRN backhaul links, and between MRN backhaul links and macro UE. The use of predictor antennas can improve CSI accuracy to enable the use of advanced interference avoidance and cancellation schemes for the backhaul links. Nevertheless, whether enhancements on the current intercell interference coordination (ICIC) framework in LTE are needed to support the use of MRNs still requires further investigation.

I have been thinking of possible use of 8x8 MIMO, this can be one possible scenario where the network may use 8x8 or even 4x4. Anyway, the complete article is embedded below:

Making LTE fit for the IoT

Another presentation from the #FWIC2013. This presentation by Vodafone covers some of the areas where the LTE standards are being tweaked for making M2M work with them without issues.

Another area is the access barring that I have blogged about before here. This will become important when we have loads of devices trying to access the network at the same time.

The presentation is embedded below and you can also listen to the audio here.

Making LTE fit for the IoT - Vodafone from Zahid Ghadialy

Big Data and Vulnerability of Cellular Systems

I am sure most of you are aware of Big Data, if not watch this video on my old post here. Moray Rumney from Agilent recently gave a talk in #FWIC on how Big Data techniques can be used to exploit the vulnerabilities in a cellular system. Though the talk focussed on GSM and 3G, it is always a good intro. The presentation embedded below:

Collecting Big Data in an Increasingly Complex Mobile World from Zahid Ghadialy

You can also listen to the audio of his presentation here.

New RRC message in Rel-11: In-device coexistence indication

I have blogged about about IDC here and here. If the eNB is interested in knowing if the device is having an interference issue it can ask the UE to send this message in the RRC Conn Reconfiguration message. The UE would send the message if it has interference issues.

Inter-frequency handover is a good solution in case the UE is experiencing interference.

From the Rel-11 whitepaper posted last week here:

To assist the base station in selecting an appropriate solution, all necessary/available assistance information for both time and frequency domain solutions is sent together in the IDC indication. The IDC assistance information contains the list of carrier frequencies suffering from on-going interference and the direction of the interference. Additionally it may also contain time domain patterns or parameters to enable appropriate DRX configuration for time domain solutions on the serving LTE carrier frequency.

Note that the network is in the control of whether or not to activate this interference avoidance mechanism. The InDeviceCoexIndication message from the UE may only be sent if a measurement object for this frequency has been established. This is the case, when the RRCConnectionReconfiguration message from the eNB contains the information element idc-Config. The existence of this message declares that an InDeviceCoexIndication message may be sent. The IDC message indicates which frequencies of which technologies are interfered and gives assistance to possible time domain solutions. These comprise DRX assistance information and a list of IDC subframes, which indicate which HARQ processes E-UTRAN is requested to abstain from using. This information describes only proposals, it is completely up to the network to do the decisions.

Connectivity in 'Connected Vehicles'

An interesting presentation from the Future of Wireless International conference about the evolution and options for connected cars and other vehicles

Connected Vehicle - Accenture from Zahid Ghadialy

3GPP Rel.11 Technology Introduction whitepaper

Another excellent summary whitepaper by R&S, embedded below:

LTE- Advanced (3GPP Rel.11) Technology Introduction from Zahid Ghadialy

Nice way of showing HetNets, by Cisco #LTEWS

This is from a presentation by Akram Awad of Cisco in the LTE World Summit 2013 in Amsterdam. I really like the way HetNets are explained

Our World Without Mobile :-)

Decision Tree of Transmission Modes (TM) for LTE

4G Americas have recently published whitepaper titled "MIMO and Smart Antennas for Mobile Broadband Systems" (available here). The above picture and the following is from that whitepaper:

Figure 3 above shows the taxonomy of antenna configurations supported in Release-10 of the LTE standard (as described in 3GPP Technical Specification TS 36.211, 36.300). The LTE standard supports 1, 2, 4 or 8 base station transmit antennas and 2, 4 or 8 receive antennas in the User Equipment (UE), designated as: 1x2, 1x4, 1x8, 2x2, 2x4, 2x8, 4x2, 4x4, 4x8, and 8x2, 8x4, and 8x8 MIMO, where the first digit is the number of antennas per sector in the transmitter and the second number is the number of antennas in the receiver. The cases where the base station transmits from a single antenna or a single dedicated beam are shown in the left of the figure. The most commonly used MIMO Transmission Mode (TM4) is in the lower right corner, Closed Loop Spatial Multiplexing (CLSM), when multiple streams can be transmitted in a channel with rank 2 or more.

Beyond the single antenna or beamforming array cases diagrammed above, the LTE standard supports Multiple Input Multiple Output (MIMO) antenna configurations as shown on the right of Figure 3. This includes Single User (SU-MIMO) protocols using either open loop or closed loop modes as well as transmit diversity and Multi-User MIMO (MU-MIMO). In the closed loop MIMO mode, the terminals provide channel feedback to the eNodeB with Channel Quality Information (CQI), Rank Indications (RI) and Precoder Matrix Indications (PMI). These mechanisms enable channel state information at the transmitter which improves the peak data rates, and is the most commonly used scheme in current deployments. However, this scheme provides the best performance only when the channel information is accurate and when there is a rich multi-path environment. Thus, closed loop MIMO is most appropriate in low mobility environments such as with fixed terminals or at pedestrian speeds.

In the case of high vehicular speeds, Open Loop MIMO may be used, but because the channel state information is not timely, the PMI is not considered reliable and is typically not used. In TDD networks, the channel is reciprocal and thus the DL channel can be more accurately known based on the uplink transmissions from the terminal (the forward link’s multipath channel signature is the same as the reverse link’s – both paths use the same frequency block). Thus, MIMO improves TDD networks under wider channel conditions than in FDD networks.

One may visualize spatial multiplexing MIMO operation as subtracting the strongest received stream from the total received signal so that the next strongest signal can be decoded and then the next strongest, somewhat like a multi-user detection scheme. However, to solve these simultaneous equations for multiple unknowns, the MIMO algorithms must have relatively large Signal to Interference plus Noise ratios (SINR), say 15 dB or better. With many users active in a base station’s coverage area, and multiple base stations contributing interference to adjacent cells, the SINR is often in the realm of a few dB. This is particularly true for frequency reuse 1 systems, where only users very close to the cell site experience SINRs high enough to benefit from spatial multiplexing SU-MIMO. Consequently, SU-MIMO works to serve the single user (or few users) very well, and is primarily used to increase the peak data rates rather than the median data rate in a network operating at full capacity.

Angle of Arrival (AoA) beamforming schemes form beams which work well when the base station is clearly above the clutter and when the angular spread of the arrival is small, corresponding to users that are well localized in the field of view of the sector; in rural areas, for example. To form a beam, one uses co-polarized antenna elements spaced rather closely together, typically lamda/2, while the spatial diversity required of MIMO requires either cross-polarized antenna columns or columns that are relatively far apart. Path diversity will couple more when the antennas columns are farther apart, often about 10 wavelengths (1.5m or 5’ at 2 GHz). That is why most 2G and 3G tower sites have two receive antennas located at far ends of the sector’s platform, as seen in the photo to the right. The signals to be transmitted are multiplied by complex-valued precoding weights from standardized codebooks to form the antenna patterns with their beam-like main lobes and their nulls that can be directed toward sources of interference. The beamforming can be created, for example, by the UE PMI feedback pointing out the preferred precoder (fixed beam) to use when operating in the closed loop MIMO mode TM4.

For more details, see the whitepaper available here.

Related posts:

• LTE-A: Downlink Transmission Mode 9 (TM-9)
• R&S Whitepaper: LTE Transmission Modes and Beamforming