Friday 2 September 2011

Multipoint HSDPA / HSPA

The following is from 3GPP TR 25.872 - Technical Specification Group Radio Access Network; HSDPA Multipoint Transmission:

HSPA based mobile internet offerings are becoming very popular and data usage is increasing rapidly. Consequently, HSPA has begun to be deployed on more than one transmit antenna or more than one carrier. As an example, the single cell downlink MIMO (MIMO-Physical layer) feature was introduced in Release 7. This feature allowed a NodeB to transmit two transport blocks to a single UE from the same cell on a pair of transmit antennas thus improving data rates at high geometries and providing a beamforming advantage to the UE in low geometry conditions. Subsequently, in Release-8 and Release-9, the dual cell HSDPA (DC-HSDPA) and dual band DC-HSDPA features were introduced. Both these features allow the NodeB to serve one or more users by simultaneous operation of HSDPA on two different carrier frequencies in two geographically overlapping cells, thus improving the user experience across the entire cell coverage area. In Release 10 these concepts were extended so that simultaneous transmissions to a single UE could occur from four cells (4C-HSDPA).

When a UE falls into the softer or soft handover coverage region of two cells on the same carrier frequency, it would be beneficial for the non-serving cell to be able to schedule packets to this UE and thereby improving this particular user’s experience, especially when the non-serving cell is partially loaded. MultiPoint HSDPA allows two cells to transmit packets to the same UE, providing improved user experience and system load balancing. MultiPoint HSDPA can operate on one or two frequencies.

Click to enlarge

There is also an interesting Qualcomm Whitepaper on related topic that is available to view and download here. The following is from that whitepaper:

The simplest form of Multipoint HSPA, Single Frequency Dual Cell HSPA (SFDC-HSPA), can be seen as an extension to the existing DC-HSPA feature. While DC-HSPA allows scheduling of two independent transport blocks to the mobile device (UE) from one sector on two frequency carriers, SFDC-HSPA allows scheduling of two independent transport blocks to the UE from two different sectors on the same carrier. In other words, it allows for a primary and a secondary serving cell to simultaneously send different data to the UE. Therefore, the major difference between SFDC-HSPA and DC-HSPA operation is that the secondary transport block is scheduled to the UE from a different sector on the same frequency as the primary transport block. The UE also needs to have receive diversity (type 3i) to suppress interference from the other cell as it will receive data on the same frequecny from multiple serving cells.Figure 1 llustrates the high-level concept of SFDC-HSPA.

In the case where the two sectors involved in Multipoint HSPA transmission belong to the same NodeB (Intra-NodeB mode), as illustrated in Figure 2, there is only one transmission queue maintained at the NodeB and the RNC. The queue management and RLC layer operation is essentially the same as for DC-HSPA.

In the case where the two sectors belong to different NodeBs (Inter-NodeB mode), as illustrated in Figure 2, there is a separate transmission queue at each NodeB. RLC layer enhancements are needed at the RNC along with enhanced flow control on the Iub interface between RNC and NodeB in order to support Multipoint HSPA operation across NodeBs. These enhancements are discussed in more detail in Section 4. In both modes, combined feedback information (CQI and HARQ-ACK/ NAK) needs to be sent on the uplink for both data streams received from the serving cells. On the uplink, the UE sends CQIs seen on all sectors using the legacy channel structure, with timing aligned to the primary serving cell.

When two carriers are available in the network, there is an additional degree of freedom in the frequency domain. Dual Frequency Dual Cell HSPA (DFDC-HSPA) allows exploiting both frequency and spatial domains by scheduling two independent transport blocks to the UE from two different sectors on two different frequency carriers. For a DC-HSPA capable UE, this is equivalent to having independent serving cells on the two frequency carriers. In Figure 3, UE1 is in DC-HSPA mode, whereas UE2 is in DFDC-HSPA mode.

Dual Frequency Four-Cell HSPA (DF4C-HSPA) can be seen as a natural extension of DFDC-HSPA, suitable for networks with UEs having four receiver chains. DF4C-HSPA allows use of the four receiver chains by scheduling four independent transport blocks to the UE from two different sectors on two different frequency carriers. DF4C-HSPA is illustrated in Figure 4.

Like SFDC-HSPA; DFDC-HSPA and DF4C-HSPA can also be intra-NodeB or inter-NodeB, resulting in an impact on transmission queue management, Iub flow control and the RLC layer.

Advantages of Multipoint transmission:
* Cell Edge Performance Improvement
* Load balancing across sectors and frequency carriers
* Leveraging RRU and distributed NodeB technology

Multipoint HSPA improves the performance of cell edge users and helps balance the load disparity across neighboring cells. It leverages advanced receiver technology already available in mobile devices compatible with Release 8 and beyond to achieve this. The system impact of Multipoint HSPA on the network side is primarily limited to software upgrades affecting the upper layers (RLC and RRC).


No comments: