Sunday 7 May 2017

10 years battery life calculation for Cellular IoT

I made an attempt to place the different cellular and non-cellular LPWA technologies together in a picture in my last post here. Someone pointed out that these pictures above, from LoRa alliance whitepaper are even better and I agree.

Most IoT technologies lists their battery life as 10 years. There is an article in Medium rightly pointing out that in Verizon's LTE-M network, IoT devices battery may not last very long.

The problem is that 10 years battery life is headline figure and in real world its sometimes not that critical. It all depends on the application. For example this Iota Pet Tracker uses Bluetooth but only claims battery life of  "weeks". I guess ztrack based on LoRa would give similar results. I have to admit that non-cellular based technologies should have longer battery life but it all depends on applications and use cases. An IoT device in the car may not have to worry too much about power consumption. Similarly a fleet tracker that may have solar power or one that is expected to last more than the fleet duration, etc.


So coming back to the power consumption. Martin Sauter in his excellent Wireless Moves blog post, provided the calculation that I am copying below with some additions:

The calculation can be found in 3GPP TR 45.820, for NB-IoT in Chapter 7.3.6.4 on ‘Energy consumption evaluation’.

The battery capacity used for the evaluation was 5 Wh. That’s about half or even only a third of the battery capacity that is in a smartphone today. So yes, that is quite a small battery indeed. The chapter also contains an assumption on how much power the device draws in different states. In the ‘idle’ state the device is in most often, power consumption is assumed to be 0.015 mW.

How long would the battery be able to power the device if it were always in the idle state? The calculation is easy and you end up with 38 years. That doesn’t include battery self-discharge and I wondered how much that would be over 10 years. According to the Varta handbook of primary lithium cells, self-discharge of a non-rechargable lithium battery is less than 1% per year. So subtract roughly 4 years from that number.

Obviously, the device is not always in idle and when transmitting the device is assumed to use 500 mW of power. Yes, with this power consumption, the battery would not last 34 years but less than 10 hours. But we are talking about NB-IoT so the device doesn’t transmit for most of the time. The study looked at different transmission patterns. If 200 bytes are sent once every 2 hours, the device would run on that 5 Wh battery for 1.7 years. If the device only transmits 50 bytes once a day the battery would last 18.1 years.

So yes, the 10 years are quite feasible for devices that collect very little data and only transmit them once or twice a day.

The conclusions from the report clearly state:

The achievable battery life for a MS using the NB-CIoT solution for Cellular IoT has been estimated as a function of reporting frequency and coupling loss. 

It is important to note that these battery life estimates are achieved with a system design that has been intentionally constrained in two key respects:

  • The NB-CIoT solution has a frequency re-use assumption that is compatible with a stand-alone deployment in a minimum system bandwidth for the entire IoT network of just 200 kHz (FDD), plus guard bands if needed.
  • The NB-CIoT solution uses a MS transmit power of only +23 dBm (200 mW), resulting in a peak current requirement that is compatible with a wider range of battery technologies, whilst still achieving the 20 dB coverage extension objective.  

The key conclusions are as follows:

  • For all coupling losses (so up to 20 dB coverage extension compared with legacy GPRS), a 10 year battery life is achievable with a reporting interval of one day for both 50 bytes and 200 bytes application payloads.
  • For a coupling loss of 144 dB (so equal to the MCL for legacy GPRS), a 10 year battery life is achievable with a two hour reporting interval for both 50 bytes and 200 bytes application payloads. 
  • For a coupling loss of 154 dB, a 10 year battery life is achievable with a 2 hour reporting interval for a 50 byte application payload. 
  • For a coupling loss of 154 dB with 200 byte application payload, or a coupling loss of 164 dB with 50 or 200 byte application payload, a 10 year battery life is not achievable for a 2 hour reporting interval. This is a consequence of the transmit energy per data bit (integrated over the number of repetitions) that is required to overcome the coupling loss and so provide an adequate SNR at the receiver. 
  • Use of an integrated PA only has a small negative impact on battery life, based on the assumption of a 5% reduction in PA efficiency compared with an external PA.

Further improvements in battery life, especially for the case of high coupling loss, could be obtained if the common assumption that the downlink PSD will not exceed that of legacy GPRS was either relaxed to allow PSD boosting, or defined more precisely to allow adaptive power allocation with frequency hopping.

I will look at the technology aspects in a future post how 3GPP made enhancements in Rel-13 to reduce power consumption in CIoT.

Also have a look this GSMA whitepaper on 3GPP LPWA lists the applications requirements that are quite handy.

2 comments:

Unknown said...

The battery life calculations in the blog refers to 3GPP TR 45.820, Chapter 7.3.6.4 which is based on Huawei/Vodafone clean slate solution. As you know that the proposed solution was based on FDMA in downlink and uplink, and is not compatible (or derived based on LTE). The final approved NB-IoT specs are mainly derived from LTE using OFDMA in DL and SC-FDMA in uplink and had many complexities compared to clean slate proposal. I doubt if the battery life calculations will be any longer valid and realizable in field.

Diogenes Senior said...

This methodology is not valid for LTE-M, where power consummation is based in eDRX mode. If we want to calculate the battery life for LTE-M we need to use eDRX parameters defined for LTE-M.