Ultrawideband (UWB) based In-building Location Systems

Continuing on yesterdays theme of Location determination. I have heard in couple of presentations that in future based on multiple RF radios that we will carry, we could be uniquely identified on the planet even though there may not be a single device identifying us uniquely.

A similar project as above but for computers is the Panopticlick project which can be found here.

UBISENSE: UWB Based In-building Location Systems

View more presentations from Zahid Ghadialy.

Locating Wireless Devices Where GPS May Not Be Available

Some of you may have read my earlier posts on stealing spectrum via Femtocells and using Femtocells abroad illegally. This presentation tries to answer one such problem on how do you find the location where GPS cannot be used. This could also be used in case of Cognitive Radios. See my old blog entry here.

OFCOM Locating Wireless Devices where GPS may not be available

View more presentations from Zahid Ghadialy.

Recap of LTE E-UTRAN and Air Interface Protocols

LTE E-UTRAN and its Access Side Protocols

View more documents from All About 4G.

You can also check out the IEEE Comsoc Video tutorial "LTE Radio Access – Physical Layer", delivered by none other than Stefan Parkvall of Ericsson. The tutorial is available at: http://host.comsoc.org/freetutorial/anritsu3/anritsu3.html

3GPP Green activities / Energy Saving initiatives

3GPP has been working on Energy saving initiatives for Release-10 and Release-11. Here is a very quick summary of some of these items.

Telecommunication management; Study on Energy Savings Management (ESM)

Most mobile network operators aim at reducing their greenhouse emissions, by several means such as limiting their networks' energy consumption.

In new generation Radio Access Networks such as LTE, Energy Savings Management function takes place especially when mobile network operators want e.g. to reduce Tx power, switch off/on cell, etc. based on measurements made in the network having shown that there is no need to maintain active the full set of NE capabilities.

By initiating this Work Item about Energy Savings Management, 3GPP hopes to contribute to the protection of our environment and the environment of future generations.

The objective of this technical work is to study automated energy savings management features. Usage of existing IRPs is expected as much as possible, e.g. Configuration Management IRP, etc. However, this technical work may identify the need for defining a new IRP.

The following operations may be considered in this study item (but not necessarily limited to):
• Retrieval of energy consumption measurements
• Retrieval of traffic load measurements
• Adjust Network Resources capabilities


OAM aspects of Energy Saving in Radio Networks

There are strong requirements from operators on the management and monitoring of energy saving functions and the evaluation of its impact on the network and service quality. Therefore an efficient and standardized Management of Energy Saving functionality is needed. Coordination with other functionalities like load balancing and optimization functions is also required.

The objectives of this work item are:
• Define Energy Savings Management OAM requirements and solutions for the following use cases,
• eNodeB Overlaid
• Carrier restricted
• Capacity Limited Network
• Define OAM requirements and solutions for coordination of ESM with other functions like
• Self-Optimization
• Self Healing
• Traditional configuration management
• Fault Management
• Select existing measurements which can be used for assessing the impact and effect of Energy Saving actions corresponding to above Energy Saving use cases.
• Define new measurements which are required for assessing the impact and effect of Energy Saving actions, including measurements of the energy consumption corresponding to above Energy Saving use cases.


Study on impacts on UE-Core Network signalling from Energy Saving

Energy Saving (ES) mechanisms are becoming an integral part of radio networks, and consequently, of mobile networks. Strong requirements from operators (for reasons of cost and environmental image) and indirectly from authorities (for the sake of meeting overall international and national targets) have been formulated. With the expected masses of mobile network radio equipment as commodities, in the form of Home NB/eNBs, this aspect becomes even more crucial.

It is necessary to ensure that ES does not lead to service degradation or inefficiencies in the network. In particular:
• the activation status of radio stations (on/off) introduces a new scale of dynamicity for the UE and network;
• mass effects in signalling potentially endanger the network stability and need to be handled properly.

It is unclear whether and how currently defined procedures are able to cope with, and eventually can be optimized for, ES conditions; thus a systematic study is needed.

The study aims, within the defined CT1 work areas, at:
• analysing UE idle mode procedures and UE-Core Network signalling resulting from frequent switch on/off of radio equipment in all 3GPP accesses, including home cell deployment and I-WLAN;
• performing a corresponding analysis for connected mode UEs;
• analysing similar impacts from activation status of non-3GPP access networks;
• documenting limitations, weaknesses and inefficiencies in these procedures, with emphasis on mass effects in the UE-Core Network signalling;
• studying potential optimizations and enhancements to these procedures;

The study shall also evaluate and give recommendations on potential enhancements to 3GPP specifications (whether and where they are seen necessary).


Study on Solutions for Energy Saving within UTRA Node B

Due to the need to reduce energy consumption within operators’ networks, and considering the large amount of UMTS network equipment deployed in the field around the world, the standardisation of methods to save energy in UMTS Node Bs is seen as an important area of study for 3GPP.There has not been a large amount of focus on energy-saving in UMTS networks so far in 3GPP, although some solutions have been agreed in Release 9. Therefore it is proposed to start an initial study phase to identify solutions and perform any initial evaluation, such that a subset of these proposals can be used as the basis for further investigation of their feasibility.

The objective is to do an initial study to identify potential solutions to enable energy saving within UMTS Node-Bs, and do light initial evaluation of the proposed solutions, with the aim that a subset of them can be taken forward for further investigation as part of a more focused study in 3GPP.

The solutions identified in this study item should consider the following aspects:
• Impacts on the time for legacy and new UEs to gain access to service from the Node B
• Impacts on legacy and new terminals (e.g. power consumption, mobility)

Some initial indication of these aspects in relation to the proposed solutions should be provided.


Study on Network Energy Saving for E-UTRAN

The power efficiency in the infrastructure and terminal should be an essential part of the cost-related requirements in LTE-A. There is a strong need to investigate possible network energy saving mechanisms to reduce CO2 emission and OPEX of operators.

Although some solutions have been proposed and part of them have been agreed in Release-9, there has not been a large amount of attention on energy saving for E-UTRAN so far. Many potential solutions are not fully shown and discussed yet. Therefore, it is proposed to start an initial study phase to identify solutions, evaluate their gains and impacts on specifications.

The following use cases will be considered in this study item:
• Intra-eNB energy saving
• Inter-eNB energy saving
• Inter-RAT energy saving

Intra-eNB energy saving, in EUTRAN network, a single cell can operate in energy saving mode when the resource utilization is sufficiently low. In this case, the reduction of energy consumption will be mainly based on traffic monitoring with regard to QoS and coverage assurance.

A lot of work on Inter-eNB energy saving has already been done for both LTE and UTRA in Rel-9. This Study Item will investigate additional aspects (if any) on top of what was already agreed for R9.

Inter-RAT energy saving, in this use case, legacy networks, i.e. GERAN and UTRAN, provide radio coverage together with E-UTRAN. For example E-UTRAN Cell A is totally covered by UTRAN Cell B. Cell B is deployed to provide basic coverage of the voice or medium/low-speed data services in the area, while Cell A enhances the capability of the area to support high-speed data services. Then the energy saving procedure can be enabled based on the interaction of E-UTRAN and UTRAN system.

The objective of this study item is to identify potential solutions for energy saving in E-UTRAN and perform initial evaluation of the proposed solutions, so that a subset of them can be used as the basis for further investigation and standardization.

Energy saving solutions identified in this study item should be justified by valid scenario(s), and based on cell/network load situation. Impacts on legacy and new terminals when introducing an energy saving solution should be carefully considered. The scope of the study item shall be as follows:
• User accessibility should be guaranteed when a cell transfers to energy saving mode
• Backward compatibility shall be ensured and the ability to provide energy saving for Rel-10 network deployment that serves a number of legacy UEs should be considered
• Solutions shall not impact the Uu physical layer
• The solutions should not impact negatively the UE power consumption

RAN2 will focus on the Intra-eNB energy saving, while RAN3 will work on Inter-RAT energy saving and potential additional Inter-eNB energy saving technology.


Study on Solutions for GSM/EDGE BTS Energy Saving

There has not been a large amount of focus on energy-saving in GSM/EDGE networks so far in 3GPP, although some solutions have been agreed in previous Releases, notably MCBTS. Therefore it is proposed to start an initial study phase to identify solutions and perform any initial evaluation, such that a subset of these proposals can be used as the basis for further investigation of their feasibility.

The objective is to study potential solutions to enable energy saving within the BTS (including MCBTS and MSR), and evaluate each proposed solutions in detail. These potential solutions shall focus on the following specific aspects
• Reduction of Power on the BCCH carrier (potentially enabling dynamic adjustment of BCCH power)
• Reduction of power on DL common control channels
• Reduction of power on DL channels in dedicated mode, DTM and packet transfer mode
• Deactivation of cells (e.g. Cell Power Down and Cell DTX like concepts as discussed in RAN)
• Deactivation of other RATs in areas with multi-RAT deployments, for example, where the mobile station could assist the network to suspend/minimise specific in-use RATs at specific times of day
• And any other radio interface impacted power reduction solutions.

The solutions identified in this study item shall also consider the following aspects:
• Impacts on the time for legacy and new mobile stations to gain access to service from the BTS
• Impacts on legacy and new mobile stations to keep the ongoing service (without increasing drop rate)
• Impacts on legacy and new mobile stations implementation and power consumption, e.g. due to reduction in DL power, cell (re-)selection performance, handover performance, etc.
• Impacts on UL/DL coverage balance, especially to CS voice

Solutions shall be considered for both BTS energy saving non-supporting and supporting mobile stations (i.e. solutions that are non-backwards compatible towards legacy mobile stations shall be out of the scope of this study).

Recap of MIMO Technologies in 3GPP LTE and LTE-Advanced

MIMO Technologies in 3GPP LTE and LTE-Advanced

View more documents from All About 4G.

1200Mbps DL with LTE-Advanced

I blogged last year about the LTE-A UE categories but then the categories were still under discussion. In the 3GPP RAN WG1#62 LTE-Advanced UE Categories were discussed based on NTT DoCoMo proposal and the data rates are as summarised in the picture above.

Note that category 8 has 1200Mbps DL and 600Mbps UL speed.

The complete report is available here.

Via: WirelessMoves.

RF Pattern Matching adopted in 3GPP Release-10

RF Pattern Matching is now a recognized unique location method in standards that provides carriers and OEMs with the ability to offer high accuracy location-based services that traditionally haven’t been available with low-accuracy Cell-ID based technologies. RF Pattern Matching will be incorporated into Release 10 of the 3G UMTS specifications, expected to become final in late 2010 or early 2011. This will also set the stage for opportunities to incorporate RF Pattern Matching into LTE and other future air interfaces.


“The decision to incorporate RF Pattern Matching into the 3G UMTS specifications is needed for all service providers wanting to provide the highest-SLA option for LBS as it gives them more credible options for public safety and commercial applications,” said Manlio Allegra, president and chief executive officer at Polaris Wireless. “This level of LBS accuracy will create an improved user experience for wireless customers, which ultimately generates additional revenue streams for carriers and other enterprises offering LBS applications.”


Polaris WLS™ is a patent-protected implementation of RF Pattern Matching, which provides the best network-based location performance in urban and indoor settings and is a perfect complement to A-GPS, enabling a best-in-class hybrid solution. Polaris’ WLS™ works without the RF Pattern Matching definition in standards, but standardization through 3GPP allows for future performance enhancements and provides flexibility for the solution and carrier implementations. Polaris’s current WLS products will continue to operate within existing standards.


By being included in the 3G UMTS standard, Polaris’ location technology has received further validation as one of the most accurate in the world. Polaris will now be considered a preferred provider to Tier 1 carriers and infrastructure vendors who want to add a high accuracy location solution to their technology mix that meets the new 3GPP standard.


The FCC is currently considering new E911 Phase II regulations that would improve indoor location capabilities for first responders. Using RF Pattern Matching, Polaris’ WLS™ software solution enables carriers and OEMs to be prepared to meet these new FCC requirements with little or no investment in new infrastructure or hardware.

RF Pattern Matching Discussion document presented in 3GPP is embedded below:

RF Pattern Matching Location Methods

View more presentations from Zahid Ghadialy.

Micro-SIM supporting 3FF format for LTE testing

Continuing yesterdays theme of Smart Cards.


I read Comprion's recent press release with regards to Micro-SIM.

As mobile devices get more and more complex, the components used become smaller and smaller. With the launch of the new LTE Test (U)SIM supporting the 3FF format, also known as Micro-SIM or Mini-UICC, COMPRION is responding to this trend. The LTE Test (U)SIM in the Mini-UICC format is only half the size of a regular Plug-In card and can be used in very small mobile devices.

Just like COMPRION's first released LTE Test (U)SIM, this new 128K/J LTE Test (U)SIM includes all new LTE data fields up to Release 9. The card has three applications implemented: a Test SIM; a Test USIM; and a Test ISIM. The Test (U)SIM also supports the three voltage classes 1.8V, 3V and 5V. Standardised commands such as "Resize" (for extending the size of a data field) and "Create" (for creating new data fields) are supported. The Test Card's flexibility and feature range enable the user to comprehensively examine the functionality of an LTE mobile device without having access to a live LTE network.

To ensure backwards compatibility to the Plug-In format, COMPRION also offers a Mini-UICC Adapter to turn the Mini-UICC into the Plug-In format. Hence, the Mini-UICC can also be used in today's mobile phones.

Its interesting to see that the new SIM is around half the size of the original and provides the same functionality. Sign of devices and components evolving.

The embedded presentation though old may be of intereste as it shows the difference between SIM, UICC and the 3FF

Smart Card Platform

View more presentations from Zahid Ghadialy.

SIMFi = SIM with WiFi

Since the beginning of this year, Sagem Orga and Telefonica have been working on next generation SIM card called SIMFi.

With SIMFi, you can convert a phone into a WiFi hotspot. The phone would use HSPA/LTE for data connectivity and at the same time it would broadcast WiFi signals for any equipment to connect to these signals and browse the web. Power consumption information have not been mentioned which I am sure would be a problem for the phone.

SIMFi Removes the need for additional accessories to facilitate transmission services (e.g. MiFi, USB modem, PCMCIA…) and can make connectivity a lot simpler, straigtforward and cheaper.

SIMFi specifications

• SIM card compatible with the latest telecom specifications.
• SIM card: ISO 2FF plug-in
• The mobile phone does not need any special features.
• Modem WiFi integrated in the SIM card, works with 802.11b.
• The modem is guided by the SIM card's tools.
• Energy-saving features (works with 2G and 3G).
• The aerial is adaptable, allowing short- and long-range operations (from 2 cm to 30 m) managed by the SIM card's tools.

HeNBs (Femtocells) and eNBs Handovers

An excerpt from presentation by Dr. Doug Pulley, picoChip. The presentation is available to download from here.